CTC Union ETU01C Manual de usuario descargar pdf (Pagina 15)

ERM01-FE1/ET100R

Fractional E1 to 10/100Base-TX

Ethernet Router Card

Fractional

The ERM01-FE1/ET100R Router Card is a single slot card that can be installed in any available slot to provide IP over E1 transmission. The

router engine uses an embedded system which can be configured and controlled from a serial port, Telnet or Web based user interface. It

supports industry standard encapsulations of PPP and HDLC as well as proprietary header for Cisco router's HDLC.

●

Features

Ethernet port IP Address/subnet mask

WAN port IP Address/subnet mask

Router Name / Password

RS-232 Console Port Management

Web/Telnet Management

WAN port IP address/subnet mask

DHCP server/client

NAT Function

Virtual Server Mapping

SNMP MIB-2 supported

Supports VPN pass through

Forwarding IP multicast support

DNS proxy server

SNTP supported

Simple Statistical

Ping and Trace route

Static Routing Setup

Routing Table (manually set up to 32 entries minimum)

Dynamic Routing RIP I & II, Send or Receive on Ethernet or WAN

PPP, HDLC and Cisco HDLC WAN protocol encapsulatoin

Flash Upgrade (via TFTP)

Hardware

Connection

WAN Speed

LAN Speed

Function

Protocols

Security

LED

Samsung ARM9 integrated communications

166MHz processor, 8MB Flash, and 32MB

pipeline RAM for code, data and buffers

1 x Ethernet LAN port (10/100)

Synchronous Port N56/N64 up to 2048Kbps

Ethernet LAN port 10/100 Mbps

Proxy Routing, IP Routing, Static Routing,

Dynamic Routing, DHCP Client/ DHCP

Server, IP Mapping, Packet Filtering

PPP, NAT, RIP 1/2, TCP/IP

PAP/CHAP, NAT, Filter

Link/ACT : On=link ; Flash=Activity

100 : On=100Base ; Off=10Base

ERM01-FE1/ET100

Fractional E1 to 10/100Base-TX

Ethernet Bridge Card

The ERM01-FE1/ET100 Bridge Card is a single slot card that can be installed in any available slot to provide Ethernet over E1 transmission. The

bridge engine uses an ASIC design for wire speed performance and supports industry standard HDLC encapsulation. The ERM01-E1U-ET100

bridge is an economical solution for LAN to LAN applications over framed or Unframed E1 transport.

●

Features

High performance bridge for 10Base-T or 100Base-TX Ethernet

extension.

Auto-MDI/MDIX detects and corrects crossed cable.

Ethernet LAN Interface on RJ-45 connector.

Transparent half / Full duplex support on WAN / LAN interface.

Automatic LAN table learning and aging.

IEEE 802.3x flow control.

Filter mode (pure bridge) or repeater mode selectable

Provides Ethernet over E1 economically

No IP address settings required

Simple DIP switch setting to control filtering, packet buffer and

Ethernet auto/forced mode

Bridge

LAN

General

LAN Table: 256 MAC address with 5 minute

automatic aging

Filtering and Forwarding : wire speed

Packet size; 64~1522 Bytes

Buffer : 340 frames

Delay : 1 frame

Standard : compliant to IEEE802.3 /803.2u

Data rate : 10Base-T / 100Base-TX, Full or Half

Duplex

Connector : RJ45

IP bridging over G.703 E1

ISO standard HDLC encapsulation

WAN Speed: Nx64 (where N=1 to 31) for Fractional

E12048Kbps for Unframed E1

5-4

PDH Series

ERM01-FE1/ET100R

www.ctcu.com

E1 CSU/ DSU Slide-in Card

Table of Contents

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 39 40

Comentarios a estos manuales

Sin comentarios

CTC Union ETU01C Manual de usuario Pagina 15

Comentarios a estos manuales

Relacionado con productos y manuales para Convertidores de medios de la red CTC Union ETU01C