CTC Union FMUX04 Manual de usuario Pagina 1

USER MANUAL FMUX04 Fiber Optical Multiplexer Standalone / Rack Type 4 Channel Fixed Design G.703 E1, T1(DS1) SNMP Manageable (Optional) FXS Order

Chapter 1: Introduction The following photo (AC model), with graphics, shows the major components which make up the FMUX04 (with the Order Wire and S

Chapter 1: Introduction 11 1.5 Technical Specifications 1.5.1 E1 Link Ports 4 fixed ports Framing Unframed (transparent) Bit Rate 2.048 Mb/s +/-50

Chapter 1: Introduction 12 1.5.3 Local Setup and Configuration DIP Switches A switch -12 pole, B switch - 2 pole Console Port local VT-100 terminal

Chapter 1: Introduction 13 1.5.6 Optical Specifications Connector Type ST, SC, FC, LC, MT-RJ or WDM-SC (single fiber) Optical mode Multi-mode or Si

Chapter 1: Introduction 14 1.5.9 Power supply Voltage (AC source) 100 ~ 240 VAC Voltage (DC range 1) 18 ~ 36 VDC Voltage (DC range 2) 36 ~ 72 VDC

Chapter 1: Introduction 1.7 T1(DS1) Signal Structure 1.7.1 T1 link line rate The T1 line operates at a nominal rate of 1.544Mb/s. 1.7.2 T1 link lin

Chapter 1: Introduction 16 This page left blank intentionally.

Chapter 2. Installation Chapter 2. Installation 2.1 General The Installation chapter will cover the physical installation of the FMUX04, Standalone/R

Chapter 2. Installation 2.4 Mechanical Assembly The FMUX04 is designed for standalone use, but it may be rack mounted as required with an optional mo

Chapter 2. Installation 2.5 Electrical Installation 2.5.1 Power connection, AC For a model with AC power supply, AC power (100~240VAC) is supplied to

Chapter 2. Installation 2.6 Rear Panel Connectors The rear panel of the FMUX04 supports the E1 and T1 interface connection, the AC or DC power connect

Chapter 2. Installation 2.8 Removal/Replacement Procedures 2.8.1 Order Wire Feature Module Removal / Replacement ***CAUTION*** This procedure should

Chapter 2. Installation 2.8.2 SNMP Feature Removal / Replacement ***CAUTION*** This procedure should only be performed by qualified service personne

Chapter 3. Operation 23 Chapter 3. Operation 3.1 Introduction This chapter will go into the details of the specific configuration and operation of the

Chapter 3. Operation 3.3 Terminal Mode Operation 24 A notebook computer has become an invaluable tool of the Systems Engineer. Connection between th

Chapter 3. Operation 3.5 Configuring in Console Mode The FMUX04 Control Port (labeled Console & Alarm on the front panel) is a console terminal

Chapter 3. Operation If a password is required to login, please enter the 4 digit password previously set. Please see 3.5.2.1 System Configuration re

Chapter 3. Operation The display window shows the status for both the local and remote multiplexers. If the optical link is broken, the remote status

Chapter 3. Operation 3.5.2.1 System Configuration Use the System Configuration menu option to save and load the single user setting, to load the fact

Chapter 3. Operation Loopback Descriptions * LLB (Optical local loop back) near end (NE) far end (FE) * RLB (Optical Remo

The information contained in this document is subject to change without prior notice. TRADEMARKS Microsoft is a registered trademark of Microsoft C

Chapter 3. Operation 3.5.2.3 E1/T1 Configuration LOCAL << E1/T1 Configuration >> 1.

Chapter 3. Operation * RLB (E1/T1 Remote loop back) near end (NE) far end (FE) This remote loop back will loop the logical chan

Chapter 3. Operation 3.5.2.5 Alarm Relay The fifth item from the ''Configure System Status' menu is the Alarm Relay Co

Chapter 3. Operation 3.5.2.7 SNMP Configuration Please refer to Chapter 4 SNMP for the configuration of the SNMP option. 3.5.2.8 Upgrade firmware us

Chapter 3. Operation Upgrade Procedure Select the upgrade option; "1" upgrade the mainboard firmware, or "2" upgrade the FPGA firm

Chapter 3. Operation 3.5.3 Display Alarm Record From the main login page, press "3" to display the alarm record. The

Chapter 3. Operation 3.6 Remote Configuration From the main login page select the second option "2", Remote Login. REMOTE

Chapter 4. SNMP 37 Chapter 4. SNMP 4.1 General The Simple Network Management Protocol (SNMP) is one of many protocols in the Internet Protocol (IP)

Chapter 4. SNMP 38 The MIB includes the definitions of relevant managed objects (MIB variables) for the specific node. Various MIB's can be defi

Chapter 4. SNMP In general, SNMP agents support two types of access rights: Read-only the SNMP agent accepts and processes only SNMP getRequest an

CTC Union Technologies Co., Ltd. Far Eastern Vienna Technology Center (Neihu Technology Park) 8F, No. 60, Zhouzi St. Neihu, Taipei, 114 Taiwan Phon

Chapter 4. SNMP 4.6.1 Configure the SNMP Agent From the 'SNMP Configuration' menu select "1", SNMP Agent Configuration.

Chapter 4. SNMP The manager configuration has the ability to setup access for up to four (4) different management workstations. The community strings

Chapter 4. SNMP 4.6.4 Save Configuration and Reboot the SNMP From the 'SNMP Configuration' menu, press "4" to sav

Chapter 4. SNMP Make sure the TFTP server is running and enter your choice of upgrade item. LOCAL <

Chapter 4. SNMP CTC Union provides a TFTP utility program that runs standalone in Windows® without any installation. We recommend that you copy the p

Chapter 4. SNMP 4.7 MIB File A MIB is a "management information base" file that allows network management software understand how to manage

Chapter 4. SNMP 4.8 Web Based Interface When the FMUX04 is installed with the SNMP option, the unit has the added management features of Telnet, SNMP

Chapter 4. SNMP 4.8.3 Display System Status The default page shown will be the Display System Status page. Note that the navigation menu is in the fra

Chapter 4. SNMP 4.8.5 System Configuration The System Configuration page is used to save and load user settings, load default settings, clear the alar

Chapter 4. SNMP 4.8.7 E1/T1 Configuration The E1/T1 configuration page sets the channel service, line code and termination type for the E1/T1. It also

Table of Contents i Chapter 1. Introduction...

Chapter 4. SNMP 4.8.9 Alarm Configuration The Alarm Relay page allows enabling or disabling the alarm relay function. (refer to 3.5.2.5)

Chapter 4. SNMP 4.8.11 SNMP Setup 4.8.11.1 SNMP Agent Configuration Configures the agent IP, subnet mask and default gateway. (refer to 4.6.1)

Chapter 4. SNMP 4.8.11.3 TFTP Server Configuration Configures the SNMP card for TFTP upgrade. (refer to 4.6.3) 4.8.11.4 Save Conf

Chapter 4. SNMP 4.8.11.5 TFTP and Upgrade Firmware Once TFTP is properly configured, this page is used to execute the upgrade for SNMP, mainboard firm

Chapter 4. SNMP 4.8.13 Display Information The Display Information page is where the current versions for main firmware, FPGA and SNMP can be displaye

Chapter 4. SNMP 55 Set IP login Password The above examples are Telnet using Windows HyperTerminal utility. The scr

Appendix A. Miscellaneous Appendix A. Miscellaneous A.1 Console port pin assignment The console port on the FMUX04 serves two purposes; it provides th

Appendix A. Miscellaneous A.3 Console cable pin assignment CAB-DB9DB9F-232-3 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 DB9F

Appendix A. Miscellaneous A.6 SNMP RJ-45 pin assignment Pin Signal Description 1 TX+ Transmit (+)* 2 TX- Transmit (-)* 3 RX+ Receive (+)* 4 NC No

Appendix A. Miscellaneous 59 A.8 SNMP Object Details Path=iso.org.dod.private.enterprise.ctc.fmux04.local Object Identifier Object Type stat Parame

Table of Contents ii 3.5.2 Define System Parameters ... 27 3.5.3 Di

Appendix A. Miscellaneous 60 Object Identifier Object Type stat Parameters local_phone_configuration RW 0 - off 1 - on local_alarm_relay R

Fiber Converter Series CTC Union Technologies Co., Ltd. Far Eastern Vienna Technology Center (Neihu Technology

Chapter 1: Introduction 7 Chapter 1. Introduction Thank you for choosing the FMUX04. If you would like to skip right to the installation and configura

Chapter 1: Introduction 8 When configured for E1 operation, the 4 channels of the FMUX04 may use either BNC (75 Ohm unbalanced) or RJ-45 (120 Ohm bal

Chapter 1: Introduction 9 When the FMUX04 is ordered with optional Order Wire, a hardware card is installed inside the unit. The front panel's R