CTC Union SHDSL Especificaciones

G.SHDSL.bis EFM Network Extender

10 1.2 Features  Extend Ethernet Services to sites with existing copper infrastructure  Increased Flexibility in Deployment  Lower Investmen

100 Telnet Console mode: User name Password Supervisor Password All function can use Can only ping test, view the sta

101 4.11.1 Upgrade main software Move the cursor ">>" to upgrade and press enter to upgrade firmware. ----------------------------

102 4.12 EXIT If you want to exit the system without saving, move the cursor " >> " to exit and press enter. ----------------

103 5 Appendix – Setup table SHDSL.bis: Mode □□□□STU-C □□□□STU-R Link type □□□□2-wire □□□□4-wire □□□□8-wire Annex Type

104 VLAN Mode: VLAN Mode □□□□Disable □□□□802.1Q Tag VLAN □□□□Port Based VLAN 802.11Q VLAN: 1 2 3 4 5 6 No. VID LAN1 LAN2 LAN3 L

105 QoS Mode: QoS Mode □□□□Disable □□□□Port Based □□□□VLAN Tag □□□□IP DSCP Queue Weight: Queue Index 0 1 2 3 Weight Value Qu

106 User Profile: User profile User name Password Attrib 1 □□□□Menu □□□□Command 2 □□□□Menu □□□□Command 3 □□□□Menu □□□□Comm

107 SNMP Community: SNMP entry (1) Validate □□□□Enable □□□□Disable Community Access Right : □□□□Read only □□□□Read Write □□□□De

11 VLAN Support 802.1Q Tag-Based VLAN Port-Based VLAN Port-Based Q-in-Q Priority Re-mapping VLAN Trunk mode QoS Support Ingress Rate control Egre

12 1.4 Applications EFM DSLAM to point connection Point to point connection

13 2 Getting to know the EFM Modem This section will introduce the hardware of the EFM modem. 2.1 Front Panel The front panel contains LED wh

14 LED status of EFM Modem : LEDs Active Description PWR On Power on On SHDSL.bis line connection is dropped ALM Blink SHDSL.bis self test MGMT

15 2.2 Rear Panel The rear panel of G.SHDSL.bis EFM Modem is where all of the connections are made. Connector Description DC-IN Power ad

16 2.2.2 LAN ports and MGMT port The EFM modem has four LAN ports and one MGMT Ethernet port. Those ports are auto-negotiating and auto-crossover.

17 2.2.4 Power connection Make sure you are using the correct power source for the AC/DC adaptor. Inset the female end of power adaptor’s cord int

18 3 Configuration use Web Browser 3.1 Configuration method There are three methods to configure the EFM modem: serial console, Telnet and Web B

19 3.2 Installation The following guide is designed to lead users through Web Configuration of G.shdsl.bis EFM Modem in the easiest and quickest w

20 3.3 Setup up with Web Browser This section introduces the configuration and functions of the web-based management. This is an HTML-based managem

21 The following is the index screen that displays when you first access the web interface. 3.4 Basic Setup The Basic Setup contains:  Operat

22 The diagram below shows the basic setup’s flowchart.

23 3.4.1 Operation mode and MGMT Click Basic for basic installation. Click CPE (Customer Premises Equipment) side or CO (Central Office) side

24 3.4.2 DHCP server Press Next to set the next page: Dynamic Host Configuration Protocol (DHCP) is a communication protocol that lets

25 For example: If the LAN IP address is 192.168.0.1, the IP range of LAN is 192.168.0.2 to 192.168.0.254. The DHCP server assigns the IP from Start

26 3.4.3 LAN Press Next to set the next page: Enter Parameters in LAN: LAN type item can been selected as: Disable, Dynamic IP or Static I

27 3.4.4 Review Press Next to set the next page: The screen will display the new configured parameters. Double check the parameters and Clic

28 3.5 Advanced Setup Note: The advanced functions are only for advanced users to setup advanced functions. The incorrect setting of advanced func

29 3.5.1.1 Line Type Line type indicates how many wires you want to use for the SHDSL.bis connection. Line Type EFM Modem 2-wire 4-wire 8-wire

CTC Union Technologies Co., Ltd. Far Eastern Vienna Technology Center (Neihu Technology Park) 8F, No. 60 Zhouzi St. Neihu District Taipei 114 Taiwa

30 3.5.1.5 SNR margin SNR margin is an index of line connection quality. You can see the actual SNR margin in STATUS SHDSL.bis. The larger is SNR

31 3.5.2 VLAN Click VLAN to configure VLAN. VLAN (Virtual Local Area Network) allows a physical network to be partitioned into multiple logical

32

33 3.5.2.1 802.1Q Tag-Based VLAN Click the 802.1Q Tag-Based VLAN to configure the EFM modem. VID: (Virtual LAN ID) is an identification numb

34 TCI (Tag Control Information field) including user priority, Canonical format indicator (CFI) and VLAN ID. TPID- defined value of 8100 in hex. Wh

35 Before enabling VLANs for the EFM modem, you must first assign each port to the VLAN group(s) in which it will participate. By default all ports

36 3.5.2.2 Port-Based VLAN Click Port-Based VLAN to configure the EFM modem. Port-Based VLANs are VLANs where the packet forwarding decision i

37 The default setting is all ports connected which means all ports can communicate with each other. That is, there are no virtual LANs. The opti

38 3.5.2.3 Port-based QinQ Click Port-Based QinQ to configure the EFM modem. PVID (Port VID): It is an untagged member from 1 to 4094 of

39 On devices of different vendors, the TPID of the outer VLAN tag of QinQ frames may have different default values. You can set or modify this TPID

Legal The information in this publication has been carefully checked and is believed to be entirely accurate at the time of publication. CTC Union T

40 3.5.3 QoS QoS (Quality of Service) refers to both a network’s ability to deliver data with minimum delay, and the networking methods used to

41 3.5.3.1 Port Based Priority When you click Port Based Priority, it will show the following: Select the ports to which the rule should be

42 BE (Best Effort) is used for data applications or any non-classified traffic. This would include e-mail, Internet browsing, data back-up etc. The

43 3.5.3.2 VLAN Tag Priority When you click VLAN Tag Priority, it will show the following: VLAN Tag Priority uses the tag field information whi

44 Priority Level Traffic Type 0 (default) Best Effort 1 Background 2 Spare 3 Excellent Effort 4 Controlled Load 5 Video, less than 100 milli

45 According to the previous two tables, we can get the mapping QoS values to Egress Queues as the following: Queue 0 1 2 3 Priority 1,2 0,3

46 3.5.3.3 IP DSCP Priority Differentiated Services (DiffServ) is a class of service (CoS) model that enhances best-effort Internet services by di

47 The following is an illustration about how the bits are used in DSCP field. Bit 0 Bit 1 Bit 2 Precedence Usage 1 1 1 7 Stays the same(li

48 When you click IP DSCP(Differentiated Services Code Point) Priority, it will show the following: Each DSCP value (from 0 to 63) is mapped to

49 3.5.4 Rate Control Click Rate Control to configure the EFM modem. Limiting bandwidth to specific users and ports helps control network congest

TABLE OF CONTENTS 1 INTRODUCTION ...

50 3.6 Status When you click STATUS You can monitor the following : SHDSL.bis EFM, MGMT, LAN and INTERFACE 3.6.1 SHDSL .Bis EFM SHDSL.bis sta

51 The below display screen is from a one pair (2 wire) model: If two EFM modems have been linked together, you can see their run-time line rate s

52 3.6.2 MGMT MGMT status will display the MGMT interface information. You can view the general status of MGMT interface and DHCP client table.

53 3.6.3 LAN LAN status will display the settings of IP type, IP address and Subnet mask. For example, this shows the IP type of LAN interface

54 3.6.4 Interface INTERFACE status includes MGMT and LAN statistics information. Octet is a group of 8 bits, often referred to as a byte. Pack

55 3.7 Administration This session introduces Administration including SECURITY and SNMP (Simple Network Management Protocol). 3.7.1 Security

56 For better security, change the Supervisor ID and Supervisor password for the EFM modem. If you don’t set them, all users can be able to access t

57 Legal address pool will setup the legal IP addresses from which authorized persons can configure the EFM modem. This is the most secure method

58 3.7.2 SNMP Simple Network Management Protocol (SNMP) provides for the exchange of messages between a network management client and a network ma

59 3.7.2.1 Community Pool To enable the delimitation of management domains, SNMP uses "communities". Each community is identified by a n

3.5.2 VLAN... 31 3.5.2.1 802.1Q

60 3.7.2.2 Trap Host Pool In the table of current trap host pool, you may also setup the trap host. SNMP trap is an unsolicited informational mess

61 3.8 Utility This section will describe the UTILITY of the EFM modem. The UTILITY menu including: SYSTEM INFO: system information, such a h

62 3.8.1 System Info For review the system information, click SYSTEM INFO. You can check the MCSV, Software Version, Chipset, Firmware Version,

63 3.8.2 Config Tool The configuration tool has three functions: load Factory Default, Restore Configuration, and Backup Configuration. Press CONF

64 3.8.3 Upgrade You can upgrade the firmware of EFM modem using the upgrade function. Press Upgrade under the UTILITY menu. Type the path and

65 3.8.4 Logout To exit the web configurator, press LOGOUT. You have to log in with your password again after you log out. This is recommended aft

66 3.8.5 Restart To restart (soft reset) the EFM modem, press Restart . When you press Restart, display screen is as following: Shown is the

67 4 Configuration use Serial Console and Telnet with Menu Driven Interface 4.1 Introduction 4.1.1 Login to the Console Interface The console p

68 User: admin Password: ***** Note: The default IP address is 192.168.1.1. The line command is "telnet 192.168.1.1" in command window mo

69 The following figure gives you an example of the menu driven interface. In the menu, you scroll up/down by pressing key I / K ; select one comman

4.4 SETUP... 74 4.4.1 SHDS

70 4.2.1 Menu tree for authorized user If you are the authorized user, the menu tree is the following:

71 If you are the authorized user, you can view the display screen as follows: 4.2.2 Menu tree for unauthorized user If you are an unauthorized

72 4.3 Enable To setup the EFM modem, move the cursor " >>" to enable and press enter key. When the screen appears, type the super

73 Command Description: Command Description enable Modify command privilege. When you login via serial console or Telnet, the EFM modem defaults

74 4.4 Setup All of the setup parameters are located in the subdirectories of setup. Move the cursor " >>" to setup and press ente

75 4.4.1.3 Annex There are two types of SHDSL .bis Annex type: Annex-AF, and Annex-BG. 4.4.1.4 TCPAM There are two TCPAM modes for SHDSL .Bis:

76 4.4.2 LAN You can setup the LAN parameters by the command lan. Move the cursor " >> " to lan and press enter. ----------------

77 4.4.3 VLAN Virtual LAN (VLAN) is defined as a group of devices on one or more LANs that are configured so that they can communicate as if they

78 4.4.3.2 802.11Q VLAN To modify the VLAN rule, move the cursor to modify and press enter. ------------------------------------------------------

79 Access The port can receive or send untagged packets Trunk The port can receive or send tagged packets 802.11Q VLAN: 1 2 3 4 5 6 No. VI

4.10 ADMINISTRATION... 94 4.10.1 User Pro

80 Use List command can show the setup table for you check: ----------------------------------------------------------------------------------------

81 4.4.4.2 Queue weight This setting can set weight value on each queue. -------------------------------------------------------------------------

82 SP(Strictly Priority) services queues based on priority only. As traffic comes into the EFM modem, traffic on the highest priority queue, Q3 is t

83 4.4.4.5 VLAN Tag Priority QoS ---------------------------------------------------------------------------- Command: setup qos vlanTagPri &l

84 4.4.4.6 IP DSCP Priority Qos Differentiated Services (DiffServ) is a class of service(CoS) model that enhances best-effort Internet services by

85 4.4.5 RATE Move the cursor " >> " to Rate and press enter. -------------------------------------------------------------------

86 ---------------------------------------------------------------------- Command: setup mgmt 1 address <ip> <netmask> Message: Please

87 To configure DHCP server, move the cursor to dhcp and press enter. >> generic DHCP server generic parameters fixed DHCP server fix

88 You can add and delete a fixed host entry via fixed command. >> add Add a fixed host entry delete Delete a fixed host entry W

89 4.4.9 Host name A Host Name is the unique name by which a network-attached. The hostname is used to identify a particular host in various forms

9 1 Introduction 1.1 Descriptions The EFM Based Network Extender (or EFM Bridge Modem) provides a flexible and friendly solution for the Etherne

90 4.5 Status You can view running system status of SHDSL.bis and interface via status command. Move cursor " >> " to status a

91 4.5.2 Interface Move cursor " >> " to interface and press enter. 4.6 Show You can view the system information, configurati

92 Move cursor " >> " to system and press enter. 4.7 Write For any changes of configuration, you must write the new config

93 4.9 Ping Ping command can use to diagnose basic network connectivity of EFM modem. Move move cursor to ping command and press enter. The ping c

94 4.10 Administration You can modify the user profile, telnet access, SNMP (Sample Network Management Protocol) and supervisor information (super

95 Move the cursor ">>" to attrib and press enter. ----------------------------------------------------------------------------- C

96 4.10.2.1 Telnet TCP port User can set up the telnet TCP port from 1 to 65534. The default port is 23. -----------------------------------------

97 4.10.3 SNMP Simple Network Management Protocol (SNMP) is the protocol not only governing network management, but also the monitoring of network

98 Read_Only Access read only Read_Write Access read and write Denied Deny all access Move the cursor to list and press enter, you can view full

99 SNMP Trap Host: Trap Host entry(1~5) Version □□□□Disable □□□□Ver.1 □□□□Ver.2 IP Address Community 4.10.4 Supervisor Password an